{"title":"Alice Soundtech","description":"","products":[{"product_id":"alice-soundtech-airswitch-3","title":"Alice Soundtech Airswitch 3 station output router (3 stereo circuits) (used)","description":"\u003cp\u003e\u003cstrong\u003eAlice Soundtech Airswitch 3\u003c\/strong\u003e station output router (3 stereo circuits) (used)\u003c\/p\u003e\n\u003cp\u003eThis 1U rack-mounting unit allows logic control and unity gain audio routing of up to three stereo studios on an offer\/accept basis and controls the radio station's profanity delay unit.\u003c\/p\u003e\n\u003cp\u003eOn-air switching is controlled via two illuminated non-latching push-buttons per studios. A further two such buttons provide control of the profanity-delay unit from the selected studio.\u003c\/p\u003e\n\u003cp\u003eSwitching is achieved using high quality nitrogen-filled gold-over-paladium relays with a minimum life rating of 20 million operations. Not surprisingly, therefore, the unit comes with an ten-year unlimited-parts guarantee. The use of relays as the switching element provides the advantage that bi-directional sources such as talkback and OB lines, DC control, etc, can also be switched. Since the audio selection of the unit is entirely passive it exhibits ruler-flat frequency response with absolutely no distortion or noise introduced.\u003cbr\u003e\u003cbr\u003eThree versions of the Alice Airswitch are available. The Alice Airswitch 1 is the basic unit allowing the switching of one stereo source (two mono sources) through to output. The \u003cstrong\u003eAlice Airswitch 3\u003c\/strong\u003e is able to switch up to three stereo sources (six mono sources) which allows for split station operation, or the routing of a telephone hybrid feed or talkback line through to the on air studio. The Alice Airswitch 5 provides switching of five stereo sources (ten mono sources) for more comprehensive routing to take place.\u003c\/p\u003e\n\u003cp\u003ePush buttons are not normally supplied with the unit since some mixers, including the Alice Air 2000, are fitted with suitable switches as standard. Most other mixers can be easily modified. Alternatively the switches can easily be accommodated in a separate switch panel.\u003c\/p\u003e\n\u003cp\u003eSuitable illuminated and engraved switch-kits are available, each containing 2 momentary switches fitted with 12 volt lamps (one kit is required per studio). The Alice Airswitch Kit 'A' contains 1 x 'On Air' and 1 x 'Offer'. Kit 'B' (only required if delay unit fitted), contains 1 x 'Delay' and 1 x 'Dump'. Control switching is standard, 'ground to operate', and lamp drivers are via open collectors.\u003c\/p\u003e\n\u003cp\u003eInputs, output and control connections are via multi-way connectors, the mains connection is via an IEC. The Airswitch come complete with a 2m mains lead.\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":31445023326254,"sku":"SALIAIRSW3U","price":350.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/alice-soundtech-airswitch.jpg?v=1578921661"},{"product_id":"alice-soundtech-monopak-stereo-to-mono-converter-used","title":"Alice Soundtech Monopak stereo to mono converter (used)","description":"\u003ch2\u003eAlice Soundtech Monopak - Used\u003c\/h2\u003e\n\u003cp\u003eThis \u003cstrong\u003eAlice Soundtech Monopak\u003c\/strong\u003e is in good condition and works perfectly. There are a few scratches but these are purely cosmetic.\u003c\/p\u003e\n\u003cp\u003eThe Alice Monopak produces a fully buffered balanced line mono output from a balanced line stereo input. Output gain is adjustable via an accessible multi-turn preset from 10dB loss to 20dB gain with reference to 0dB input on both left and right inputs. \u003c\/p\u003e\n\u003cp\u003eHoused in a convenient 1U aluminum case, the Monopak can be free standing, easily mounted into a woodwork system, or fitted into a rack with use of the Alice Rack-Panel. Balanced audio inputs and mono balanced outputs are via Neutrik XLR connectors and the mains input is via IEC.\u003c\/p\u003e\n\u003ch2\u003eTechnical Specification:     \u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eInputs impedance: 20k ohms unbalanced\u003c\/li\u003e\n\u003cli\u003eFrequency response: 20Hz to 20kHz ±0.2dB\u003c\/li\u003e\n\u003cli\u003eCommon mode rejection: \u0026gt;60dB\u003c\/li\u003e\n\u003cli\u003eNoise at units gain: -100dB +8dBu\u003c\/li\u003e\n\u003cli\u003eDistortion (THD): \u0026lt;0.005% (1kHz +8dBu output)\u003c\/li\u003e\n\u003cli\u003eMax input level: +25dBu\u003c\/li\u003e\n\u003cli\u003eGain Range: -10dB to 20dB\u003c\/li\u003e\n\u003cli\u003eOutput impedance: \u0026lt;1 ohm balanced and floating\u003c\/li\u003e\n\u003cli\u003eMax output level: +25dBu\u003c\/li\u003e\n\u003cli\u003eMains voltage specification: 230v AC 50Hz 3VA \u003c\/li\u003e\n\u003cli\u003eDimensions (mm): 254(w) x 113(d) x 44(h)\u003c\/li\u003e\n\u003cli\u003eWeight (boxed): 1.05kg\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":31445023588398,"sku":"SALIMONOPAKU","price":80.0,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/alice-soundtech-monopak-used.jpg?v=1578921662"},{"product_id":"alice-soundtech-sum-diff-pak-sum-and-difference-matrix-used","title":"Alice Soundtech Sum \u0026 Diff Pak sum and difference matrix (used)","description":"\u003ch2\u003eAlice Soundtech Sum \u0026amp; Diff Pak - Used\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eWe may have multiple of this unit and conditions of units may vary, before purchase please confirm the unit pictured is the unit for sale. Updated pictures can be provided. If you don't chat with us prior to purchase we can not guarantee you will receive the unit pictured.\u003c\/strong\u003e\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":31445023719470,"sku":"SALISUMDIFFPAKU","price":125.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/alice-soundtech-sum-diff-pak.jpg?v=1578921662"},{"product_id":"alice-matchpak-1-used","title":"Alice Matchpak 1 unbalanced to balanced converter - Used","description":"\u003ch2\u003eAlice Matchpak 1 - Used\u003c\/h2\u003e\n\u003cp\u003eThis used \u003cstrong\u003eAlice MatchPak\u003c\/strong\u003e is in good condition with some cosmetic marks. This MatchPak has been powered up but not fully tested so we cannot guarantee it is in full working condition. There are no noticeable faults with the unit when powered up and Power LED illuminates with no problems. All I\/O connectors are in good condition and firmly attached to the unit.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWe may have multiple of this unit and conditions of units may vary, before purchase please confirm the unit pictured is the unit for sale. Updated pictures can be provided. If you don't chat with us prior to purchase we can not guarantee you will receive the unit pictured.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe Alice MatchPak is a unit that allows you to connect your consumer \/ hobbyist gear to your pro audio gear.This unit will interface a -10dbV audio level to a +4dbm input to feed unbalanced computer audio to your mixer or stage setup. Designed in England by Alice Soundtech, this is a SUPERB sounding active interface that is built to last a lifetime. Featuring IEC power input and holes to mount it to the inside of a rack, this is a terrific piece of gear that will simplify and improve your audio interfacing life! IEC cable not included.\u003c\/p\u003e\n\u003cp\u003eWith RCA inputs, balanced XLR outputs as well as XLR inputs with RCA outputs and with adjustable gain both ways (AND on both channels), this device has everything you need to connect different pieces of gear in your studio or on stage. Perfect for interfacing things like tape decks, computers, and other consumer gear into the pro gear world.\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":31663013036078,"sku":"SALIMATCHPAK1U","price":67.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/Matchpac-_1.jpg?v=1582726525"},{"product_id":"alice-soundtech-msu-10-used","title":"Alice Soundtech MSU-10 - Used","description":"\u003ch2\u003eAlice Soundtech MSU-10 - Used\u003c\/h2\u003e\n\u003cp\u003eThis \u003cstrong\u003eAlice Soundtech MSU-10\u003c\/strong\u003e is intended to allow quality monitoring of 10 stereo line-level sources and features built-in 10 + 10 watt power amplifiers to drive 8-ohm loudspeakers. A headphone jack is also provided with a separate level control. A loudspeaker mute input allows the unit to be used in areas with live microphones. Unity gain balanced line-level outputs permit the MSU10 also to function as a source pre-select unit. Level meters may be either PPM- or VU-type. Line-level audio connections are via XLRs and are electronically balanced.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThis is a used item. It is in very good condition with some minor signs of use. Please see images.\u003c\/strong\u003e\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":31663013101614,"sku":"SALIMSU10PPMU","price":199.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/SALIMSU10PPMU-1.jpg?v=1650463639"},{"product_id":"alice-soundtech-promatch-1-used","title":"Alice Soundtech Promatch 1 - Used","description":"\u003ch2\u003eAlice Soundtech Pro Match 1\u003c\/h2\u003e\n\u003cp\u003eThis used \u003cstrong\u003eAlice Pro Match 1\u003c\/strong\u003e is in good condition but features some cosmetic marks. The\u003cstrong\u003e Alice Pro Match 1 Unbalanced\u003c\/strong\u003e To Balanced Converter Alice Pro Match 1 Unbalanced To Balanced Converter. The Alice Promatch is a single direction pro interface unit for interfacing unbalanced domestic or semi-professional stereo sources, for example a domestic CD player or tuner to professional balanced line level inputs. The Promatch 1 for interfacing 1 stereo source. Housed in a convenient 1U aluminum case, the Promatch can be free standing, easily mounted into a woodwork system, or fitted into a rack with use of the Alice Rack-Panel. Unbalanced audio inputs are via phono connectors and balanced outputs are via Neutrik XLR type.\u003c\/p\u003e\n\u003cp\u003eWe may have multiple of this item, if you require more than one please contact us for availability. Picture may not be of the unit as picture will be take once the previous item has been sold, if you require up to date images place contact us prior to your purchase.\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":31663013330990,"sku":"SALIPROMATCH1U","price":59.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/front_8_2.jpg?v=1580743298"},{"product_id":"alice-soundtech-da6-2-xlr-dual-6-output-distribution-amplifier","title":"Alice Soundtech DA6-2 - XLR - Dual 6 Output Distribution Amplifier","description":"\u003ch2\u003eAlice Soundtech DA6-2 - XLR - Dual 6 Output Distribution Amplifier\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eAlice DA6-2 MKII\u003c\/strong\u003e is a 19” rack mounted high-performance, dual six output distribution amplifier designed to provide multiple audio feeds in stereo and dual mono applications. It can also be configured as a single twelve output distribution amplifier by the operation of internal links.\u003cbr\u003e\u003cbr\u003eAll audio connections are via professional standard XLR connectors and 25 way D-Sub. Both versions have their inputs via a pair of female Neutrik XLRs. Outputs are available in two options i) XLRs (12 x male carrying individual outputs) and D-Subs (2 x male 25 way D-Subs, one for left and one for right using the TascamTM wiring standard).\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNOTE: This unit has XLR output connectors.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eAll inputs and outputs are electronically balanced and floating and may therefore be unbalanced individually if required (see below). Note that unbalancing any input or output has no effect whatsoever on the level or balanced nature of the remaining inputs and outputs, so any combination of balanced and unbalanced equipment can be accommodated.\u003cbr\u003e\u003cbr\u003eThe input impedance of the DA6 2MKII is factory set to 20K ohms but may be changed to 600 ohms through the operation of internal links. Audio levels may be adjusted via the multi-turn trim pots located on the front panel.\u003cbr\u003e\u003cbr\u003eConnection of unbalanced equipment requires pin 3 of the XLR connector to be strapped to pin 1 (pin numbers are generally moulded into both plugs and sockets). The unbalanced connections are then made to pin1\/3 (ground) and pin 2 (signal).\u003c\/p\u003e\n\u003ch3\u003eTechnical Specification\u003cbr\u003e\n\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput impedance\u003c\/strong\u003e: internally selectable 20k ohms or 600 ohms balanced\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput: common-mode rejection\u003c\/strong\u003e: 60dB typical\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFrequency response\u003c\/strong\u003e: 20Hz to 20kHz ±0.2dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhase shift\u003c\/strong\u003e: 20Hz \u0026lt;1° 20kHz\u0026lt;5°\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNoise\u003c\/strong\u003e: -100dB (RMS 30Hz to 15kHz) at unity gain – Ref + 8dBu output\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDistortion\u003c\/strong\u003e: (THD) + 8dBu output: 40Hz 0.006% – 1kHz 0.006% 10kHz 0.02%\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutput impedance\u003c\/strong\u003e: \u0026lt;1 ohm balanced and floating\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMinimum load\u003c\/strong\u003e: 600 ohms\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGain range\u003c\/strong\u003e: adjustable up to 20dB gain and 10dB loss\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax. input level\u003c\/strong\u003e: +28dBu\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax. output level\u003c\/strong\u003e: +26dBu into 5k ohms +24dBu into 600 ohms 0dBu = 0.775 volts RMS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMains supply\u003c\/strong\u003e: 85v to 250v AC operation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower consumption\u003c\/strong\u003e: 20VA\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCase details\u003c\/strong\u003e: 1U 19″ rack mounting, overall depth 165mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShipping Weight\u003c\/strong\u003e: 1.95Kg\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Alice Soundtech","offers":[{"title":"Default","offer_id":32637453729838,"sku":"SALIDA62XLR","price":342.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/SALIDA62XLR-front2.jpg?v=1599644367"},{"product_id":"alice-soundtech-da6-2-d-sub-dual-6-output-distribution-amplifier","title":"Alice Soundtech DA6-2 - D-SUB - Dual 6 Output Distribution Amplifier","description":"\u003ch2\u003eAlice Soundtech DA6-2 - D-SUB\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eAlice DA6-2 MKII\u003c\/strong\u003e is a 19” rack mounted high-performance, dual six output distribution amplifier designed to provide multiple audio feeds in stereo and dual mono applications. It can also be configured as a single twelve output distribution amplifier by the operation of internal links.\u003cbr\u003e\u003cbr\u003eAll audio connections are via professional standard XLR connectors and 25 way D-Sub. Both versions have their inputs via a pair of female Neutrik XLRs. Outputs are available in two options i) XLRs (12 x male carrying individual outputs) and D-Subs (2 x male 25 way D-Subs, one for left and one for right using the TascamTM wiring standard).\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNOTE: This unit has D-Sub output connectors.\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eAll inputs and outputs are electronically balanced and floating and may therefore be unbalanced individually if required (see below). Note that unbalancing any input or output has no effect whatsoever on the level or balanced nature of the remaining inputs and outputs, so any combination of balanced and unbalanced equipment can be accommodated.\u003cbr\u003e\u003cbr\u003eThe input impedance of the DA6 2MKII is factory set to 20K ohms but may be changed to 600 ohms through the operation of internal links. Audio levels may be adjusted via the multi-turn trim pots located on the front panel.\u003cbr\u003e\u003cbr\u003eConnection of unbalanced equipment requires pin 3 of the XLR connector to be strapped to pin 1 (pin numbers are generally moulded into both plugs and sockets). The unbalanced connections are then made to pin1\/3 (ground) and pin 2 (signal).\u003c\/p\u003e\n\u003ch3\u003eTechnical Specification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput impedance\u003c\/strong\u003e: internally selectable 20k ohms or 600 ohms balanced\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput: common-mode rejection\u003c\/strong\u003e: 60dB typical\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFrequency response\u003c\/strong\u003e: 20Hz to 20kHz ±0.2dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhase shift\u003c\/strong\u003e: 20Hz \u0026lt;1° 20kHz\u0026lt;5°\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNoise\u003c\/strong\u003e: -100dB (RMS 30Hz to 15kHz) at unity gain – Ref + 8dBu output\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDistortion\u003c\/strong\u003e: (THD) + 8dBu output: 40Hz 0.006% – 1kHz 0.006% 10kHz 0.02%\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutput impedance\u003c\/strong\u003e: \u0026lt;1 ohm balanced and floating\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMinimum load\u003c\/strong\u003e: 600 ohms\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGain range\u003c\/strong\u003e: adjustable up to 20dB gain and 10dB loss\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax. input level\u003c\/strong\u003e: +28dBu\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax. output level\u003c\/strong\u003e: +26dBu into 5k ohms +24dBu into 600 ohms 0dBu = 0.775 volts RMS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMains supply\u003c\/strong\u003e: 85v to 250v AC operation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower consumption\u003c\/strong\u003e: 20VA\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCase details\u003c\/strong\u003e: 1U 19″ rack mounting, overall depth 165mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShipping Weight\u003c\/strong\u003e: 1.95Kg\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Alice Soundtech","offers":[{"title":"Default","offer_id":32637453795374,"sku":"SALIDA6DSUB","price":342.0,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/SALIDA62XLR-front2_db849f44-2439-4104-ae80-f8542ca8d2fa.jpg?v=1599646169"},{"product_id":"alice-soundtech-timecode-da-ltc-timecode-distribution-amplifier","title":"Alice Soundtech Timecode DA - LTC Timecode Distribution Amplifier","description":"\u003ch2\u003eAlice Soundtech Timecode DA - LTC Timecode Distribution Amplifier\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eAlice Timecode DA\u003c\/strong\u003e is a 19” rack-mounted timecode distribution amplifier, with six Neutrik audio outputs and six BNC outputs for PSC cameras and field audio mixers.\u003c\/p\u003e\n\u003ch3\u003eTechnical Specification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput impedance\u003c\/strong\u003e: internally selectable 20k ohms or 600 ohms balanced\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput: common-mode rejection\u003c\/strong\u003e: 60dB typical\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFrequency response\u003c\/strong\u003e: 20Hz to 20kHz ±0.2dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhase shift\u003c\/strong\u003e: 20Hz \u0026lt;1° 20kHz\u0026lt;5°\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNoise\u003c\/strong\u003e: -100dB (RMS 30Hz to 15kHz) at unity gain – Ref + 8dBu output\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDistortion\u003c\/strong\u003e: (THD) + 8dBu output: 40Hz 0.006% – 1kHz 0.006% 10kHz 0.02%\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutput impedance\u003c\/strong\u003e: \u0026lt;1 ohm balanced and floating\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMinimum load\u003c\/strong\u003e: 600 ohms\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGain range\u003c\/strong\u003e: adjustable up to 20dB gain and 10dB loss\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax. input level\u003c\/strong\u003e: +28dBu\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax. output level\u003c\/strong\u003e: +26dBu into 5k ohms +24dBu into 600 ohms\u003c\/li\u003e\n\u003cli\u003e0dBu = 0.775 volts RMS\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMains supply\u003c\/strong\u003e: 85v to 250v AC operation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower consumption\u003c\/strong\u003e: 20VA\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCase details\u003c\/strong\u003e: 1U 19″ rack mounting, overall depth 165mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShipping weight\u003c\/strong\u003e: 1.95Kg\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Alice Soundtech","offers":[{"title":"Default","offer_id":32637456842798,"sku":"SALITIMECODEDA","price":562.35,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/SALITIMECODEDA_1.jpg?v=1599668705"},{"product_id":"alice-soundtech-linepak-stereo-line-driver","title":"Alice Soundtech LinePAK - Stereo Line Driver","description":"\u003ch2\u003eAlice Soundtech LinePAK - Stereo Line Driver\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eAlice LinePak MKII\u003c\/strong\u003e is a dual balanced-input to balanced-output amplifier with variable gain via accessible multi-turn pre-sets on the front panel.\u003cbr\u003e\u003cbr\u003eAudio inputs and outputs on the LinePak-MKII are via Neutrik connectors and may be wired unbalanced if required, enabling the unit to be used for unbalanced to balanced conversion or vice versa, or as a convenient line buffer amplifier.\u003cbr\u003e\u003cbr\u003eMains input is via a UK IEC connector with supplied lead (2m).\u003cbr\u003e\u003cbr\u003eRack mountable kit is supplied as standard.\u003cbr\u003e\u003c\/p\u003e\n\u003ch3\u003eTechnical Specification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput impedance\u003c\/strong\u003e: 20k ohms balanced\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFrequency response\u003c\/strong\u003e: 20Hz to 20kHz ±0.2dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommon-mode rejection\u003c\/strong\u003e: \u0026gt;60dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNoise at unity gain\u003c\/strong\u003e: –100dB ref. +8dBu\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDistortion\u003c\/strong\u003e: \u0026lt;0.005% 1kHz, +8dBu output\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCrosstalk\u003c\/strong\u003e: better than -95dB at 1kHz\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGain adjustment\u003c\/strong\u003e: 10dB loss to 22dB gain\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax. input level\u003c\/strong\u003e: +25dBu\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax. output level\u003c\/strong\u003e: +25dBu\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutput impedance\u003c\/strong\u003e: \u0026lt;1 ohm balanced and floating\u003c\/li\u003e\n\u003cli\u003e0dBu = 0.775 volts RMS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMains supply\u003c\/strong\u003e: 230 V AC 3VA (115V available to order)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower consumption\u003c\/strong\u003e: 3VA\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDimensions\u003c\/strong\u003e: 275 (W) x 115 (D) x 42 (H)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShipping Weight\u003c\/strong\u003e: 1.25Kg\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Alice Soundtech","offers":[{"title":"Default","offer_id":32637457301550,"sku":"SALILINEPAK","price":237.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/SALILINEPAK_1.jpg?v=1599647337"},{"product_id":"alice-soundtech-matchpak-stereo-unbalanced-to-balanced-converter","title":"Alice Soundtech MatchPAK - Stereo Unbalanced to Balanced Converter","description":"\u003ch2\u003eAlice Soundtech MatchPAK - Stereo Unbalanced to Balanced Converter\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eAlice MatchPak MKII\u003c\/strong\u003e is a bi-directional stereo unit for interfacing unbalanced semi-pro equipment to professional balanced line-levels. Fitted with four Neutrik connectors for balanced and four RCA sockets for unbalanced connections allowing ideal signal conversion for use with domestic\/semi-professional recording\/replay equipment.\u003cbr\u003e\u003cbr\u003eSupplied set for a nominal 14dB attenuation line to equipment and a nominal 14dB gain equipment to line. Multi-turn pre-sets are provided, accessible through the front panel.\u003cbr\u003e\u003cbr\u003eMains input is via a UK IEC connector with supplied lead (2m).\u003cbr\u003e\u003cbr\u003eRack mountable kit is supplied as standard.\u003cbr\u003e\u003c\/p\u003e\n\u003ch3\u003e\n\u003cbr\u003eTechnical Specification\u003c\/h3\u003e\n\u003ch4\u003eBalanced input to unbalanced output:\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput impedance:\u003c\/strong\u003e 20k ohms\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommon-mode rejection\u003c\/strong\u003e: \u0026gt;60dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax. input level\u003c\/strong\u003e: +26dBu\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutput impedance\u003c\/strong\u003e: less than 2k ohms\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFrequency response\u003c\/strong\u003e: 20Hz to 20kHz +0dB – 0.1dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNoise\u003c\/strong\u003e: \u0026lt;-100dB ref. + 8dBu input\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDistortion\u003c\/strong\u003e: (THD): 0.005%\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClipping level\u003c\/strong\u003e: +26dBu at input\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGain range\u003c\/strong\u003e: -26dB to -6dB\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eUnbalanced input to balanced output:\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput impedance\u003c\/strong\u003e: 22k ohms\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutput impedance\u003c\/strong\u003e: less than 1 ohm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFrequency response\u003c\/strong\u003e: 20Hz to 20kHz +0dB – 0.1dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNoise\u003c\/strong\u003e: \u0026lt;-94dB ref. + 8dBu output\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDistortion\u003c\/strong\u003e: (THD): 0.005%\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClipping level\u003c\/strong\u003e: +26dB into 5k ohms. +21dB into 600ohms\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGain range\u003c\/strong\u003e: 6dB to 26dB\u003c\/li\u003e\n\u003cli\u003e0dBu = 0.775 volts RMS\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMains supply\u003c\/strong\u003e: 230 V AC (115V available to order)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower consumption\u003c\/strong\u003e: 3.2VA\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDimensions\u003c\/strong\u003e: 275 (W) x 115 (D) x 42 (H)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShipping Weight\u003c\/strong\u003e: 1.25Kg\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Alice Soundtech","offers":[{"title":"Default","offer_id":32637460152366,"sku":"SALIMATCHPAK","price":243.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/SALIMATCHPAK_1.jpg?v=1599648280"},{"product_id":"alice-soundtech-monopak-stereo-to-dual-mono-converter","title":"Alice Soundtech MonoPAK - Stereo to Dual Mono Converter","description":"\u003ch2\u003eAlice Soundtech MonoPAK - Stereo to Dual Mono Converter\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eAlice MonoPAK MKII\u003c\/strong\u003e produces a fully buffered balanced-line dual mono output from a balanced-line stereo input. Both mono outputs are electronically buffered and are independently adjustable via multi-turn pre-sets accessible through the front panel providing 10dB loss to 20dB gain with reference to 0dB input on both left and right inputs. Bridging-balanced audio inputs and mono-balanced outputs are via Neutrik XLR connectors and can be wired unbalanced if required.\u003cbr\u003e\u003cbr\u003eMains input is via a UK IEC connector with supplied lead (2m). Rack mountable kit is supplied as standard.\u003cbr\u003e\u003c\/p\u003e\n\u003ch3\u003eTechnical Specification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput impedance\u003c\/strong\u003e: \u0026gt;20k ohms balanced\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFrequency response\u003c\/strong\u003e: 20Hz to 20kHz +0dB – 0.1dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommon-mode rejection\u003c\/strong\u003e: \u0026gt;60dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNoise at unity gain\u003c\/strong\u003e: -100dB ref. +8dBu\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDistortion\u003c\/strong\u003e: \u0026lt;0.005% 1kHz +8dBu output\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax. input level\u003c\/strong\u003e: +25dBu\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax. output level\u003c\/strong\u003e: +25dBu\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutput impedance\u003c\/strong\u003e: \u0026lt;1 ohm balanced and floating\u003c\/li\u003e\n\u003cli\u003e0dBu = 0.775 volts RMS\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMains supply\u003c\/strong\u003e: 230 V AC (115V available to order)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower consumption\u003c\/strong\u003e: 3VA\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDimensions\u003c\/strong\u003e: 275 (W) x 115 (D) x 42 (H)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShipping Weight\u003c\/strong\u003e: 1.25Kg\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Alice Soundtech","offers":[{"title":"Default","offer_id":32637460938798,"sku":"SALIMONOPAK","price":237.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/SALIMONOPAK_1.jpg?v=1599667158"},{"product_id":"alice-soundtech-mpx-da-multiplex-distribution-amplifier","title":"Alice Soundtech MPX DA - Multiplex Distribution Amplifier","description":"\u003ch2\u003eAlice Soundtech MPX DA - Multiplex Distribution Amplifier\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eAlice rack mounted multiplex distribution amplifier\u003c\/strong\u003e is designed to provide multiple MPX feeds to main \u0026amp; standby transmission systems, automatic change-over units, silence detectors and remote monitoring facilities.\u003cbr\u003e\u003cbr\u003eA single input provides six buffered outputs.\u003cbr\u003e\u003cbr\u003eLevel adjustment is available on the front panel.\u003c\/p\u003e\n\u003ch3\u003eTechnical Specification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eImpedance\u003c\/strong\u003e: 75 ohms\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput\/Output Connectors\u003c\/strong\u003e: BNC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFrequency response\u003c\/strong\u003e: 20Hz to 20kHz ±0.2dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhase shift\u003c\/strong\u003e: 20Hz \u0026lt;1° 20kHz\u0026lt;5°\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFrequency Response\u003c\/strong\u003e: (THD) + 10dBu: 10Hz -0.03dB, 1kHz 0.00dB and 80kHz +0.02dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDistortion\u003c\/strong\u003e: +10dBu @ 1kHz -87dBu (0.004%) and +19 @ 1kHz -90dBu (0.003%)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNoise Figure\u003c\/strong\u003e: ~98dB Unweighted\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGain range\u003c\/strong\u003e: adjustable from -10dB to +20dB\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMains supply\u003c\/strong\u003e: 85v to 250v AC operation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower consumption\u003c\/strong\u003e: 20VA\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCase details\u003c\/strong\u003e: 1U 19″ rack mounting, overall depth 165mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShipping Weight\u003c\/strong\u003e: 1.95Kg\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Alice Soundtech","offers":[{"title":"Default","offer_id":32637460971566,"sku":"SALIMPXDA","price":574.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/SALIMPXDA-front.jpg?v=1599667617"},{"product_id":"alice-501t-500-series-mic-pre-with-transformers","title":"Alice 501T - 500-Series Mic Pre with Transformers","description":"\u003ch2\u003eAlice 501T - 500-Series Mic Pre with Transformers\u003c\/h2\u003e\n\u003cp\u003e\u003cspan\u003eThe \u003cstrong\u003eAlice 501T\u003c\/strong\u003e is a high-performance transformer balanced microphone preamplifier. The 501 T is designed around Alice's legendary XTX131v2 matchamp \u003cspan data-mce-fragment=\"1\"\u003ewhich achieves a noise performance which is typically less than 0.5dB from theoretical Johnsons noise.\u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e\u003cspan data-mce-fragment=\"1\"\u003eNext the mic amplifier itself. This is a discrete specially designed amplifier produced by Alice. It’s brilliantly stable and has excellent gain range, it’s almost impossible to overload so it does not need an overload indicator. The gain control gives plenty of range to use all mic types from ribbon mics up to studio condenser types. \u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e\u003cspan data-mce-fragment=\"1\"\u003eTo retain best possible quality of the audio, the output goes through another transformer, this gives you isolated balanced output and perfect matching to any line level input. The front panel has switching for phantom power, a rotary gain control and a phase switch which changes the polarity of the audio from positive to negative. \u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003cbr\u003e\n\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e500 series module standard\u003c\/li\u003e\n\u003cli\u003eBalanced transformer mic input\u003c\/li\u003e\n\u003cli\u003eMic input with wide step less gain\u003c\/li\u003e\n\u003cli\u003eLED output level metering\u003c\/li\u003e\n\u003cli\u003eSwitchable phantom power\u003c\/li\u003e\n\u003cli\u003eSwitchable 75Hz high pass filter\u003c\/li\u003e\n\u003cli\u003eSwitchable polarity reverse (phase)\u003c\/li\u003e\n\u003cli\u003eTransformer balanced line output\u003c\/li\u003e\n\u003cli\u003e100% made in the UK\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003cbr\u003e\n\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eFrequency response linearity +0, -0.4dB 10Hz to 20KHz\u003c\/li\u003e\n\u003cli\u003eMinimum gain: 32dB\u003c\/li\u003e\n\u003cli\u003eMaximum gain: 78dB\u003c\/li\u003e\n\u003cli\u003eMaximum output +24dBu floating transformer balanced\u003c\/li\u003e\n\u003cli\u003eNoise level (measured at 60dB gain) 126.8dB below input 20Hz to 20KHz\u003c\/li\u003e\n\u003cli\u003eHarmonic distortion (at 0dB output 1KHz) 2nd order 0.005%, 3rd order 0.03%\u003c\/li\u003e\n\u003cli\u003eHigh Pass Filter 6dB\/8ve 3dB down at 75Hz\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Alice Soundtech","offers":[{"title":"Default","offer_id":37988913152178,"sku":"SALI501T","price":288.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/SALI501T-2.jpg?v=1610721565"},{"product_id":"alice-503-500-series-mic-pre-with-limiter","title":"Alice 503 - 500-Series Mic Pre with Limiter","description":"\u003ch2\u003eAlice 503 - 500-Series Mic Pre with Limiter\u003c\/h2\u003e\n\u003cp\u003eThe\u003cstrong\u003e Alice 503\u003c\/strong\u003e is a microphone pre-amp and limiter in a 500 series format. The circuitry of the pre-amp is designed to get full warmth from any professional microphone whilst also achieving that 'fairy dust sound'.\u003c\/p\u003e\n\u003cp\u003eBoth microphone and line level inputs maintain excellent overload margins as well as extreme low noise performance. The audio gain in the system is shared across four low-noise amplifier stages to handle the most difficult of sounds.\u003c\/p\u003e\n\u003cp\u003eThe limiter\/compressor is a classic Ted Fletcher design from 1979 when it was first introduced into the Alice 828 portable mixer and is known to have gained admiration and is used by top artists and major studios just for the sound of the limiter!\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTechnical Specification\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMic input: 20Hz to 20KHz – precision balanced +0, -1dB\u003c\/li\u003e\n\u003cli\u003eLine input: 10KHz\u003c\/li\u003e\n\u003cli\u003eRelative input noise: -128.6dB\u003c\/li\u003e\n\u003cli\u003eHarmonic distortion: (@ 0dB output 1KHz) 2nd order 0.005%, 3rd order 0.03dB\u003c\/li\u003e\n\u003cli\u003eMaximum mic gain: 77dB\u003c\/li\u003e\n\u003cli\u003eMaximum input level: approx -10dBu\u003c\/li\u003e\n\u003cli\u003eMaximum output level: +22dBu\u003c\/li\u003e\n\u003cli\u003eHigh pass filter: 6dB\/8ve 3dB down at 75Hz\u003c\/li\u003e\n\u003cli\u003eLimiter: soft knee with approx 12:1 ratio\u003c\/li\u003e\n\u003cli\u003eSwitchable phantom power: In\/out\u003c\/li\u003e\n\u003cli\u003eSwitchable mic\/line: In\/Out\u003c\/li\u003e\n\u003cli\u003eSwitchable limiter: In\/Out\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Alice Soundtech","offers":[{"title":"Default","offer_id":37989012504754,"sku":"SALI503","price":275.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/SALI503-1.jpg?v=1610723159"},{"product_id":"alice-mic-amp-pak-duo-with-usb-output","title":"Alice Mic Amp Pak DUO with USB Output","description":"\u003ch2\u003eAlice Mic Amp Pak DUO with USB Output\u003c\/h2\u003e\n\u003cp\u003e\u003cspan\u003eThe \u003cstrong\u003eAlice Mic Amp PAK\u003c\/strong\u003e is a dual channel mic amp \u003c\/span\u003eideal for remote presenters and contributors to radio and TV shows using an existing microphone and the USB output into a PC or laptop.\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThe Mic Amp PAK features audio transformer inputs and a sophisticated discrete input stage, gain control and balanced output. A USB output on the duo version, each channel appearing as a mono feed on the left and right outputs.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTechnical Specification\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMin gain: 33.4dB\u003c\/li\u003e\n\u003cli\u003eMax gain: 79.7dB\u003c\/li\u003e\n\u003cli\u003eFrequency response:  20Hz to 20KHz +\/- 1dB\u003c\/li\u003e\n\u003cli\u003eNoise:  127.7dB below input at 70dB gain measured against 200ohm input 20Hz to 20KHz bandwidth\u003c\/li\u003e\n\u003cli\u003eHigh pass filter switch: 12dB\/8ve 3dB point 75Hz\u003c\/li\u003e\n\u003cli\u003eHarmonic distortion: measured at 50dB gain –\u003c\/li\u003e\n\u003cli\u003eAt 95Hz  2\u003csup\u003end\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder  -74dB, 3\u003csup\u003erd\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -80dB. (0.02%)\u003c\/li\u003e\n\u003cli\u003eAt 1KHz  2\u003csup\u003end\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -84dB, 3\u003csup\u003erd\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -72dB. (0.018%)\u003c\/li\u003e\n\u003cli\u003eAt 3.5KHz 2\u003csup\u003end\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -80dB, 3\u003csup\u003erd\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -63dB. (0.08%)\u003c\/li\u003e\n\u003cli\u003ePhantom power switch: 48 volts\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Alice Soundtech","offers":[{"title":"Default","offer_id":37989683101874,"sku":"SALIMICAMPPAKDUOUSB","price":458.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/SALIMICAMPPAKDUOUSB-1.jpg?v=1610730732"},{"product_id":"alice-mic-amp-pak-solo-with-usb-output","title":"Alice Mic Amp Pak SOLO with USB Output","description":"\u003ch2\u003eAlice Mic Amp Pak SOLO with USB Output\u003c\/h2\u003e\n\u003cp\u003e\u003cspan\u003eThe\u003cstrong\u003e Alice Mic Amp PAK\u003c\/strong\u003e is a single channel mic amp,  ideal for remote presenters and contributors to radio and TV shows using an existing microphone and the USB output into a PC or laptop.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eThe Mic Amp PAK  features audio transformer input and a sophisticated discrete input stage, gain control and balanced output. A USB output on the solo version apears as dual mono feed on both left and right channels.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTechnical Specification\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMin gain: 33.4dB\u003c\/li\u003e\n\u003cli\u003eMax gain: 79.7dB\u003c\/li\u003e\n\u003cli\u003eFrequency response:  20Hz to 20KHz +\/- 1dB\u003c\/li\u003e\n\u003cli\u003eNoise: 127.7dB below input at 70dB gain measured against 200ohm input 20Hz to 20KHz bandwidth\u003c\/li\u003e\n\u003cli\u003eHigh pass filter switch: 12dB\/8ve 3dB point 75Hz\u003c\/li\u003e\n\u003cli\u003eHarmonic distortion: measured at 50dB gain –\u003c\/li\u003e\n\u003cli\u003eAt 95Hz  2\u003csup\u003end\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder  -74dB, 3\u003csup\u003erd\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -80dB. (0.02%)\u003c\/li\u003e\n\u003cli\u003eAt 1KHz  2\u003csup\u003end\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -84dB, 3\u003csup\u003erd\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -72dB. (0.018%)\u003c\/li\u003e\n\u003cli\u003eAt 3.5KHz 2\u003csup\u003end\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -80dB, 3\u003csup\u003erd\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -63dB. (0.08%)\u003c\/li\u003e\n\u003cli\u003ePhantom power switch: 48 volts\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Alice Soundtech","offers":[{"title":"Default","offer_id":37989706105010,"sku":"SALIMICAMPPAKSOLOUSB","price":377.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/products\/SALIMICAMPPAKSOLOUSB-1.jpg?v=1610731654"},{"product_id":"alice-538t-500-series-stereo-opto-compressor-with-transformers","title":"Alice 538T - 500-Series Stereo OPTO Compressor with Transformers","description":"\u003ch2\u003eAlice 538T - 500-Series Stereo OPTO Compressor with Transformers\u003c\/h2\u003e\n\u003cp\u003eThe Alice 538T is a stereo 500 series Optical compressor. This unique design is a feed forward design, and also features a width control meaning more creative effects can be achieved with this compressor that other analogue designs.  \u003c\/p\u003e\n\u003cp\u003eThe ‘538T’ is designed for creative compression effects that are difficult to achieve with plug-ins. It’s capable of extreme compression just as Ted’s original Joe Meek SC2 V5;\u003cspan\u003e \u003c\/span\u003e\u003cem\u003eamazing drum sounds!\u003c\/em\u003e\u003cspan\u003e \u003c\/span\u003eIt’s also super-quality ‘Levelling Amplifier’ with the sparkle of a well-designed opto compressor\u003c\/p\u003e\n\u003ch4\u003eMechanical\u003c\/h4\u003e\n\u003cp\u003eThe 538T occupies two spaces in a standard API 500 series rack using normal ins and outs for left and right\u003c\/p\u003e\n\u003ch4\u003eInputs \u0026amp; Outputs\u003c\/h4\u003e\n\u003cp\u003eLeft and Right balanced or unbalanced inputs\u003c\/p\u003e\n\u003cp\u003eLeft and Right balanced outputs via hand matched OEP Z3001C canned transformers\u003c\/p\u003e\n\u003ch4\u003eWidth Control\u003c\/h4\u003e\n\u003cp\u003eIn order to retain perfect symmetry between the left and right channels of the stereo equaliser the audio signal is processed into ‘sum and difference’ mode (that is L+R = ‘sum’, L-R = ’difference’), the two audio signals are then processed by the EQ controls before being re-processed back into left and right format. By going through this process the left and right channels remain perfectly symmetrical with no image shift, any minor difference between the processed sum and difference signals show up only as small deviations in width of the stereo image. A further useful advantage of the sum and difference processing is that the width of the stereo image is controlled by the volume level of the ‘difference’ channel so by adding a gain control the stereo width can be accurately controlled. With the width control at minimum the audio output is mono. When the control is half way, the processing accurately recombines the audio into left and right. If the control is increased further, the image is extended beyond the original stereo.\u003c\/p\u003e\n\u003ch4\u003eMetering\u003c\/h4\u003e\n\u003cp\u003eEasy-to-read analogue meter reading audio (UV) or compression depth (comp)\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003cbr\u003e\n\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInputs\u003c\/strong\u003e: 10K impedance differential balanced.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutputs\u003c\/strong\u003e: Floating balanced 50 ohm. Max balanced output approx. +26dBu\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGain\u003c\/strong\u003e: Maximum 24dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNoise\u003c\/strong\u003e: At least 80dB below operating level Dynamic range exceeds 100dB.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHarmonic Distortion\u003c\/strong\u003e: Generally within 0.005%. 2nd order harmonic distortion rises at lower frequencies under compression.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAmplitude Frequency response\u003c\/strong\u003e: Line in 20Hz to 20KHz within 1dB.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAudio Crosstalk\u003c\/strong\u003e: the 538 uses M\/S processing (sum and difference) with ‘side’ content variable via the width control. With width set at 100% L\/R crosstalk can be better than -50dB.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompressor\u003c\/strong\u003e: Photoresistive servo operated feedback type· Ratio non-linear; minimum approx. 1.2 to 1 maximum approx. 8 to 1. Sidechain filtered for correct bass compression.Attack time 1mS min. 10mS max. (variable) Release time 200mS min 1.5S max. (variable)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnections\u003c\/strong\u003e: via 2 X 500 series sockets.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower\u003c\/strong\u003e: 3 Watts. Powered from 500 series rack. +ve rail 68mA, -ve rail 106mA.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHousing\u003c\/strong\u003e: 2 spaces of 500 series rack.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":43127396958386,"sku":"SALI538T","price":645.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/SALI538T-1_1.jpg?v=1687353436"},{"product_id":"alice-dual-ppm-box","title":"Alice Dual PPM Box","description":"\u003ch2 class=\"product_title entry-title\"\u003eDual Twin PPM’s with Sifam 74A and 74B meters\u003c\/h2\u003e\n\u003cp\u003eThe Alice dual twin PPM meter boxes are used for live on-air monitoring and in post-production facilities and for monitoring left\/right and sum\/difference signals.\u003c\/p\u003e\n\u003cp\u003eFitted with brand new Sifam 74A \u0026amp; 74B meters, Alice 704 drive cards and comes with white LED meter illumination as standard.\u003c\/p\u003e\n\u003cp\u003eAudio connectivity is via Neutrik connectors with a loop-through.\u003c\/p\u003e\n\u003cp\u003eThe free standing box is powered by 110\/240v fused mains IEC.\u003c\/p\u003e\n\u003cp\u003eMeters are setup for BBC spec – IEC 60268-10 Type IIA.\u003c\/p\u003e\n\u003cp\u003e100% manufactured in the UK.\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":55120719511926,"sku":"SALIDUALPPMBOX","price":795.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/AliceDualPPMBoxFront.jpg?v=1735893198"},{"product_id":"alice-tieline-mhb","title":"Alice Tieline MHB","description":"\u003ch2\u003eAlice MHB Tieline Extender\u003c\/h2\u003e\n\u003cp\u003eThe Alice MHB unit is a microphone input extender for the popular Tieline ViA audio codec. The ViA unit has additional audio ports with can be connected to the MHB which then give two additional microphone inputs and left \u0026amp; right headphone monitoring. \u003c\/p\u003e\n\u003cp\u003ePowered by an internal 9v battery or ‘plug-top’ power supply.\u003c\/p\u003e\n\u003cp\u003eConnections via captive audio leads.\u003c\/p\u003e\n\u003cp\u003eTechnical Specification\u003cbr\u003e\u003cstrong\u003eInput:\u003c\/strong\u003e common-mode rejection: 60dB typical\u003cbr\u003e\u003cstrong\u003eFrequency response:\u003c\/strong\u003e 20Hz to 20kHz ±0.2dB\u003cbr\u003e\u003cstrong\u003ePhase shift:\u003c\/strong\u003e 20Hz \u0026lt;1° 20kHz\u0026lt;5°\u003cbr\u003e\u003cstrong\u003eNoise:\u003c\/strong\u003e -100dB (RMS 30Hz to 15kHz) at unity gain - Ref + 8dBu output\u003cbr\u003e\u003cstrong\u003eDistortion:\u003c\/strong\u003e (THD) + 8dBu output: 40Hz 0.006% - 1kHz 0.006% 10kHz 0.02%\u003cbr\u003e\u003cstrong\u003eOutput impedance:\u003c\/strong\u003e \u0026lt;1 ohm balanced and floating\u003cbr\u003e\u003cstrong\u003eMinimum load:\u003c\/strong\u003e 600 ohms\u003cbr\u003e\u003cstrong\u003eGain range:\u003c\/strong\u003e adjustable up to 20dB gain and 10dB loss\u003cbr\u003e\u003cstrong\u003eMax. input level:\u003c\/strong\u003e +28dBu\u003cbr\u003e\u003cstrong\u003eMax. output level:\u003c\/strong\u003e +26dBu into 5k ohms +24dBu into 600 ohms\u003cbr\u003e0dBu = 0.775 volts RMS\u003cbr\u003e\u003cstrong\u003ePower supply:\u003c\/strong\u003e 230v AC to 12v DC mains adaptor or internal PP9 battery\u003cbr\u003e\u003cstrong\u003eCase details:\u003c\/strong\u003e 145 x 145 x 60mm\u003cbr\u003e\u003cstrong\u003eShipping weight:\u003c\/strong\u003e 1.50Kg\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":55120743694710,"sku":"SALITIELINEMHB","price":330.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/AliceTielineMHBFront.jpg?v=1735898931"},{"product_id":"alice-504t-mic-pre-with-limiter-and-transformers-500-series","title":"Alice 504T Mic Pre with Limiter and Transformers - 500 Series","description":"\u003ch2\u003eAlice 504T Mic Pre with Limiter and Transformers - 500-Series\u003c\/h2\u003e\n\u003cp\u003eThe microphone input uses unique circuitry, via a transformer, as is designed to get full warmth from any professional microphone while at the same time having that ‘fairy dust sound’.\u003c\/p\u003e\n\u003cp\u003eBoth microphone and line level inputs maintain excellent overload margins as well as extreme low noise performance. The audio gain in the system is shared across four low-noise amplifier stages to handle the most difficult of sounds.\u003c\/p\u003e\n\u003cp\u003eThe limiter is a classic Ted Fletcher design from 1979 when it was first introduced into the Alice 828 portable mixer and is known to have gained admiration and is used by top artists and major studios just for the sound of the limiter!\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTechnical Specification\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMic input:\u003c\/strong\u003e 20Hz to 20KHz – precision balanced +0, -1dB\u003cbr\u003e\u003cstrong\u003eLine input:\u003c\/strong\u003e 10KHz\u003cbr\u003e\u003cstrong\u003eRelative input noise:\u003c\/strong\u003e -128.6dB\u003cbr\u003e\u003cstrong\u003eHarmonic distortion:\u003c\/strong\u003e (@ 0dB output 1KHz) 2nd order 0.005%, 3rd order 0.03dB\u003cbr\u003e\u003cstrong\u003eMaximum mic gain:\u003c\/strong\u003e 77dB\u003cbr\u003e\u003cstrong\u003eMaximum input level:\u003c\/strong\u003e approx -10dBu\u003cbr\u003e\u003cstrong\u003eMaximum output level:\u003c\/strong\u003e +22dBu\u003cbr\u003e\u003cstrong\u003eHigh pass filter:\u003c\/strong\u003e 6dB\/8ve 3dB down at 75Hz\u003cbr\u003e\u003cstrong\u003eLimiter:\u003c\/strong\u003e soft knee with approx 12:1 ratio\u003cbr\u003e\u003cstrong\u003eSwitchable phantom power:\u003c\/strong\u003e In\/out\u003cbr\u003e\u003cstrong\u003eSwitchable mic\/line:\u003c\/strong\u003e In\/Out\u003cbr\u003e\u003cstrong\u003eSwitchable limiter:\u003c\/strong\u003e In\/Out\u003c\/p\u003e\n\u003cp\u003e100% manufactured in the UK\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":55120850518390,"sku":"SALI500504T","price":328.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/Alice504TMicPreFront1_0245a390-9b2b-4461-93e5-64fa740dfb1a.jpg?v=1735898292"},{"product_id":"alice-505-baxandall-stereo-eq-with-transformer-outputs","title":"Alice 505 Baxandall Stereo EQ with Transformer Outputs - 500 Series","description":"\u003ch2\u003eAlice 505 Baxandall Stereo EQ with Transformer Outputs - 500 Series\u003c\/h2\u003e\n\u003cp\u003eEqualizers were first used in the movie industry in the USA to solve a serious problem; microphone placement was difficult and the dialogue sounds achieved varied significantly, so they needed to design electronic circuits that would equalize the sounds from different microphones so that they all sounded the same. The name has stuck and now we have complex digital equalizers that engineers use for effect. The original purpose was to sweeten the sound.\u003c\/p\u003e\n\u003cp\u003eThe equalizer circuits were originally designed by Peter J Baxandall in the 1950’s as part of a competition where he won a wrist watch. Variations of his designs have been used by nearly all broadcasters and HiFi manufacturers ever since. Ted Fletchers variations incorporate the original class A circuitry and modifications to the curve have been shaped specifically for sweetening of final masters.\u003c\/p\u003e\n\u003ch3\u003eWidth Control\u003c\/h3\u003e\n\u003cp\u003eIn order to retain perfect symmetry between the left and right channels of the stereo equaliser the audio signal is processed into ‘sum and difference’ mode (that is L+R = ‘sum’, L-R = ’difference’), the two audio signals are then processed by the EQ controls before being re-processed back into left and right format. By going through this process the left and right channels remain perfectly symmetrical with no image shift, any minor difference between the processed sum and difference signals show up only as small deviations in width of the stereo image. A further useful advantage of the sum and difference processing is that the width of the stereo image is controlled by the volume level of the ‘difference’ channel so by adding a gain control the stereo width can be accurately controlled. With the width control at minimum the audio output is mono. When the control is half way, the processing accurately recombines the audio into left and right. If the control is increased further, the image is extended beyond the original stereo.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTechnical Specification\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFrequency response:\u003c\/strong\u003e 20Hz to 20KHz\u003cbr\u003e\u003cstrong\u003eLine input:\u003c\/strong\u003e 10KHz current-mode transformer balanced\u003cbr\u003e\u003cstrong\u003eGain:\u003c\/strong\u003e Unity\u003cbr\u003e\u003cstrong\u003eEQ – high:\u003c\/strong\u003e +\/- 12dB with shelving at 10kHz\u003cbr\u003e\u003cstrong\u003eEQ – mids:\u003c\/strong\u003e +\/- 12dB with shelving at 1600Hz\u003cbr\u003e\u003cstrong\u003eEQ – lows:\u003c\/strong\u003e +\/- 12dB with shelving at 100Hz\u003cbr\u003e\u003cstrong\u003eRelative input noise:\u003c\/strong\u003e better than -90dB\u003cbr\u003e\u003cstrong\u003eHarmonic distortion:\u003c\/strong\u003e \u0026lt;0.05%\u003cbr\u003e\u003cstrong\u003eCrosstalk:\u003c\/strong\u003e better than -50dB\u003cbr\u003e\u003cstrong\u003eMaximum output:\u003c\/strong\u003e +21dBu\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":55120872571254,"sku":"SALI500505EQ","price":288.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/Alice505BaxandallStereoEQFront.jpg?v=1735899424"},{"product_id":"alice-match-amp-xtx-131-v2","title":"Alice Match Amp XTX 131 MkII","description":"\u003ch2\u003eAlice Match Amp XTX 131 MkII including Loom and Pot\u003c\/h2\u003e\n\u003cp\u003eThe Matchamp XTX131 v2 is a very high-performance balanced microphone amplifier module which achieves a noise performance which is typically less than 0.5dB from theoretical Johnson’s noise when used with 150–200-ohm microphones.\u003c\/p\u003e\n\u003cp\u003eThe device achieves this high performance by eliminating the need to employ an input transformer and offers improved frequency response, noise performance, distortion, signal handling and common mode rejection ratio over typical transformer microphone input stages.\u003c\/p\u003e\n\u003cp\u003eThe significant improvement in common mode rejection makes the device particularly useful for location recording and outside broadcasts where high levels of interference are common. The device achieves 40 to 50dB better CMRR than most transformer designs at high audio and low RF frequencies. An RF filter circuit is incorporated within the device which gives further interference protection. The unit is extremely small (30 x 20 x 15mm) PCB mounting module with 0.1” spacing.\u003c\/p\u003e\n\u003cp\u003eThe XTX131 MKII replaces the earlier XTX131 MKI and XTX129. The unit is supplied with a ready-built mic amp PCB, cable loom and 2k5 reverse-logic potentiometer.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTechnical Specification\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSupply voltage:\u003c\/strong\u003e +\/- 15 to 20 volts DC\u003cbr\u003e\u003cstrong\u003eCurrent consumption:\u003c\/strong\u003e 16mA per rail\u003cbr\u003e\u003cstrong\u003eMaximum input level:\u003c\/strong\u003e 24dBu\u003cbr\u003e\u003cstrong\u003eMaximum output level:\u003c\/strong\u003e 23dBu\u003cbr\u003e\u003cstrong\u003eMinimum load impedance:\u003c\/strong\u003e 600 ohms\u003cbr\u003e\u003cstrong\u003ePerformance at 60dB gain with a 150 ohm source:\u003c\/strong\u003e -131dB (30Hz-15kHz)\u003cbr\u003e\u003cstrong\u003eCommon mode rejection ratio:\u003c\/strong\u003e 105dB @ 10kHz\u003cbr\u003e\u003cstrong\u003eDistortion at 0dBu output:\u003c\/strong\u003e 0.006% THD\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":55120887578998,"sku":"SALIXTX131MKII","price":99.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/AliceMatchAmpXTX131MkIIFront.jpg?v=1735900166"},{"product_id":"alice-538r-rack-opto-stereo-compressor","title":"Alice 538R Rack Opto Stereo Compressor","description":"\u003ch2\u003eAlice 538R Rack Opto Stereo Compressor with Transformers\u003c\/h2\u003e\n\u003cp\u003eThe Alice 538R is a full size mains powered 1U rack-mounted version of our popular 538T OPTO stereo compressor from the 500 Lunchbox series.\u003c\/p\u003e\n\u003cp\u003eThe 538R has OEP transformer balanced inputs and outputs, a side-chain input and dual VU meters.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTed Fletcher’s historic opto compression design\u003c\/li\u003e\n\u003cli\u003ePerfect ‘Hard-Wired’ by-pass for instant comparisons\u003c\/li\u003e\n\u003cli\u003eWide range ratios from gentle to brutal\u003c\/li\u003e\n\u003cli\u003eAccurate UV compression metering on a real meter\u003c\/li\u003e\n\u003cli\u003eExtreme stereo width control\u003c\/li\u003e\n\u003cli\u003eSide-chain\u003c\/li\u003e\n\u003cli\u003eShielded hand-matched audio transformers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe ‘538R’ is designed for creative compression effects that are difficult to achieve with plug-ins. It’s capable of extreme compression just as Ted Fletcher’s original Joe Meek SC2 V5;\u003cspan\u003e \u003c\/span\u003e\u003cem\u003eamazing drum sounds!\u003c\/em\u003e\u003cspan\u003e \u003c\/span\u003eIt’s also super-quality ‘Levelling Amplifier’ with the sparkle of a well-designed opto compressor.\u003c\/p\u003e\n\u003ch3\u003eMechanical\u003c\/h3\u003e\n\u003cp\u003eThe 538R is a 1U rackmounted unit using mains voltage.\u003c\/p\u003e\n\u003ch3\u003eInputs \u0026amp; Outputs\u003c\/h3\u003e\n\u003cp\u003eLeft and Right transformer balanced inputs and outputs are via hand matched OEP canned transformers\u003c\/p\u003e\n\u003cp\u003eSide-chain via a 6.35mm stereo TRS connector\u003c\/p\u003e\n\u003ch3\u003eWidth Control\u003c\/h3\u003e\n\u003cp\u003eIn order to retain perfect symmetry between the left and right channels of the stereo equaliser the audio signal is processed into ‘sum and difference’ mode (that is L+R = ‘sum’, L-R = ’difference’), the two audio signals are then processed by the EQ controls before being re-processed back into left and right format. By going through this process the left and right channels remain perfectly symmetrical with no image shift, any minor difference between the processed sum and difference signals show up only as small deviations in width of the stereo image. A further useful advantage of the sum and difference processing is that the width of the stereo image is controlled by the volume level of the ‘difference’ channel so by adding a gain control the stereo width can be accurately controlled. With the width control at minimum the audio output is mono. When the control is half way, the processing accurately recombines the audio into left and right. If the control is increased further, the image is extended beyond the original stereo.\u003c\/p\u003e\n\u003ch3\u003eMetering\u003c\/h3\u003e\n\u003cp\u003eEasy-to-read stereo analogue meters reading audio (UV) or compression depth (comp)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eINPUTS\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e· 10K impedance differential balanced.\u003cbr\u003e\u003cstrong\u003eOUTPUTS\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e· Floating balanced 50 ohm.  Max balanced output approx. +26dBu\u003cbr\u003e\u003cstrong\u003eGAIN\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e· Maximum 24dB\u003cbr\u003e\u003cstrong\u003eNOISE\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e· At least 80dB below operating level. Dynamic range exceeds 100dB.\u003cbr\u003e\u003cstrong\u003eHARMONIC DISTORTION\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e· Generally within 0.005%. 2\u003csup\u003end\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder harmonic distortion rises at lower frequencies under compression.\u003cbr\u003e\u003cstrong\u003eAMPLITUDE FREQUENCY RESPONSE\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e· Line in 20Hz to 20KHz within 1dB.\u003cbr\u003e\u003cstrong\u003eAUDIO CROSSTALK\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e· the 538 uses M\/S processing (sum and difference) with ‘side’ content variable via the width control. With width set at 100% L\/R crosstalk can be better than -50dB.\u003cbr\u003e\u003cstrong\u003eCOMPRESSOR\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e· Photoresistive servo operated feedback type· Ratio non-linear;  minimum approx. 1.2 to 1 maximum approx. 8 to 1. Sidechain filtered for correct bass compression. Attack time 1mS min. 10mS max. (variable) Release time 200mS min 1.5S max. (variable)\u003cbr\u003e\u003cstrong\u003eCONNECTIONS\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e· via Neutrik XLR and TRS connectors\u003cbr\u003e\u003cstrong\u003ePOWER\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e· 85 to 285v AC\u003cbr\u003e\u003cstrong\u003eHOUSING\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e· 19″ 1U rackmount unit\u003cbr\u003eSupplied with 2m IEC cable\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":55120951181686,"sku":"SALI538ROPTOCOMP","price":885.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/Alice538RRackStereoOPTOCompressorFront1.jpg?v=1735901138"},{"product_id":"alice-4061s-stereo-forward-feed-compression-amplifier","title":"Alice 4061S Stereo Forward-Feed Compression Amplifier","description":"\u003ch2\u003eAlice 4061S Stereo Forward-Feed Compression Amplifier\u003c\/h2\u003e\n\u003cp\u003eA stereo pair of audio inputs feed via XLR or balanced jack connectors via output routing relays to precision balancing transformers working in Ted Fletcher’s ‘current mode’  design which produces extremely linear output with minimal distortion. An illuminated ‘compressor’ switch operates the input relays switching the output connectors from direct (or by-pass) to compressed (compressor output). The stereo audio then enters a ‘sum and difference’ matrix where a width control affects the ‘difference’ signal and sets the stereo image width.\u003c\/p\u003e\n\u003cp\u003eA feed from the ‘sum’ signal feeds filter networks and is converted to a carefully regulated DC current with controls for the speed of attack and decay. The ‘sum and difference’ (M and S) audio feeds direct to a pair of current controlled (transconductance) amplifiers which are gain controlled by the DC control current and operate in feedback around a pair of precision low distortion operational amplifiers. Buffer amplifiers convert the compressed M and S audio back to ‘left and right’, they are affected by the ‘gain make up’ control and drive specialist high quality output transformers. Balanced outputs are available on both XLR and jack connectors. Audio volume level is shown on a pair of illuminated peak programme meters developed specifically for the PYE 4061S project. An illuminated switch selects either a normal mode of left and right outputs, or the left meter showing a mono (sum) signal from a point before the output ‘gain make up’ control, and a measure of gain\u003cbr\u003ereduction on the right meter.\u003c\/p\u003e\n\u003cp\u003e• \u003cstrong\u003eINPUTS\u003c\/strong\u003e 20Kohms transformer balanced, XLR and TRS jack\u003cbr\u003e• \u003cstrong\u003eOUTPUTS\u003c\/strong\u003e 56 ohms transformer balanced, XLR and TRS jack\u003cbr\u003e• \u003cstrong\u003eAMPLITUDE FREQUENCY RESPONSE\u003c\/strong\u003e +0 -0.2dB 20Hz to 20KHz\u003cbr\u003e(40Hz to 10KHz within 0.06dB)\u003cbr\u003e• \u003cstrong\u003eHARMONIC DISTORTION\u003c\/strong\u003e at 1KHz at normal operating level 0.01%\u003cbr\u003e2nd order 0.03% 3rd order. LF distortion dependent on release\u003cbr\u003esettings\u003cbr\u003e• \u003cstrong\u003eNOISE\u003c\/strong\u003e approx. 110dB below peak operating level\u003cbr\u003e• \u003cstrong\u003eSYSTEM GAIN\u003c\/strong\u003e max 30dB.\u003cbr\u003e• \u003cstrong\u003eMAX LEVELS,\u003c\/strong\u003e INPUT +30dBu, OUTPUT +28dBu\u003cbr\u003e• \u003cstrong\u003eNORMAL OPERATING LEVEL\u003c\/strong\u003e limited to +8dB peak\u003cbr\u003e• \u003cstrong\u003eWEIGHT\u003c\/strong\u003e 2.8Kgs\u003cbr\u003e• \u003cstrong\u003ePOWER\u003c\/strong\u003e 95 to 245VAC 5 watts max\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":55121265557878,"sku":"SALI4061S","price":1650.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/AlicePYE4061SStereoFFCompressorFront.jpg?v=1735914879"},{"product_id":"alice-dual-riaa-phono-pak-mkii","title":"Alice Dual RiAA Phono PAK MkII","description":"\u003ch2\u003e\u003cspan\u003eDual Stereo RiAA Turntable Pre-Amp PAK\u003c\/span\u003e\u003c\/h2\u003e\n\u003cp\u003eAlice dual stereo RiAA amplifier MKII\u003c\/p\u003e\n\u003cp\u003eThe Alice dual RiAA pre-amplifier has been redesigned for broadcast use with quality vinyl records. We also included an additional feature to cater for the vinyl mastering community by including a high output stage at very low distortion levels.\u003c\/p\u003e\n\u003cp\u003eThe dual stereo preamplifiers closely meet the exact RIAA specifications with extended frequency range at both LF and HF frequencies.\u003c\/p\u003e\n\u003cp\u003eThe unit has been designed, laid out and constructed with particular care to minimize hum and noise from power supplies and external sources.\u003c\/p\u003e\n\u003cp\u003eThe unit is rack mountable and is mains powered using an integrated circuit switch mode supply that can operate from any mains voltage between 85 and 285 volts ac.\u003c\/p\u003e\n\u003cp\u003eThe Alice RiAA (advanced phono pre-amplifier) has been specifically designed for transcription and broadcast use with quality vinyl records. The dual stereo preamplifiers closely meet the exact RIAA specifications with extended frequency range at both LF and HF frequencies. The unit has been designed, laid out and constructed with particular care to minimize hum and noise from power supplies and external sources.\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eFACILITIES\u003cbr\u003eInputs are via two pairs of RCA type phono connector sockets. The upper (white) socket is for the left amplifier and the lower (red) socket is for the right amplifier. Outputs are via 3-pin XLR type sockets for left and right outputs. Main’s input is via IEC mains socket. A blue LED indicates that power has been applied.\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eADJUSTMENTS\u003cbr\u003eMultiturn pre-set controls (between the input and output terminations) give output level control to match various pickup types. As new, the unit is set to give outputs in the range of -10dBu for most professional moving magnet pickups. The range of control available via the pre-set is 14dB. Removal of the top cover exposes the circuitry and a series of headers that can be set. Headers H1 to H4 offer different capitative loads to the pickup. Altering the loading will affect the high frequency response. As new, the headers are set to the left-hand position and this is likely to be correct for most pickups. Headers H5 to H8 are to enable or disable high-pass filters for the 4 channels. With the links to the left the filters are disabled. The filters may be enabled (links to the right) to minimize ultralow frequency sensitivity that can cause problems with tracking. The high-pass filters are 12dB\/8ve with the 3dB point set at 18Hz. So they are not audible in operation. Headers H9 to H12 are to enable ‘normal’ or ‘high’ audio output level. With the links to the left the outputs are ‘normal’, that is, approx. -10dBu. With the links to the right the outputs are increased to 0dB. (0.775VRMS) \u003c\/p\u003e\n\u003cp\u003eMains ground is internally connected to audio ground\u003cbr\u003eSupplied with a 2m IEC mains cable (UK 13amp plug)\u003cbr\u003eMains supply: 85 to 285 VAC\u003cbr\u003ePower consumption: 2VA\u003cbr\u003eDimensions: 275 (W) x 115 (D) x 42 (W)\u003cbr\u003eShipping weight: 1.20kg\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":55121280008566,"sku":"SALIDUALRIAAPAKMKII","price":330.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/DualRiAAPhonoPakMkIIFront.jpg?v=1735915834"},{"product_id":"alice-1228-mkiii-mixing-desk-12x-mic-line-channels","title":"Alice 1228 MkIII Mixing Desk 12x Mic\/Line Channels","description":"\u003ch2\u003eAlice 1228 MkIII Mixing Desk 12x Mic\/Line Channels\u003c\/h2\u003e\n\u003cp\u003eWe are now shipping the Alice 1228 MK3 mixer with 12 mic \/ mono line inputs.\u003c\/p\u003e\n\u003cp\u003eThe 1228 series mixer went into production at the Alice factory in Windsor in 1976 and the last one was made there in 1986.\u003c\/p\u003e\n\u003cp\u003eThe Mk3 was designed by Ted Fletcher during late 2019 with production starting in August 2021. It only took 43 years for the MK3 verison to be made!\u003c\/p\u003e\n\u003cp\u003e12 x microphone and mono line inputs \u0026amp; line outputs are transformer balanced. All microphone inputs c\/w 48v phantom powering. Monitor cut and a remote control relays are available at time of ordering.\u003c\/p\u003e\n\u003cp\u003eIt comes in standard gun metal gray\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":55121372512630,"sku":"SALI1228MKIII","price":2450.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/Alice1228MkIIIMixingDesk1.jpg?v=1735919579"},{"product_id":"alice-mic-amp-pak-transformer-solo-without-usb","title":"Alice Mic Amp PAK Transformer Solo without USB","description":"\u003ch2\u003eAlice Mic Amp PAK Transformer Solo without USB\u003c\/h2\u003e\n\u003cp\u003eThe Alice Mic Amp PAK is a single channel mic amp with a audio transformer input and a sophisticated discrete input stage, gain control and balanced output.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTechnical Specification\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMin gain:\u003c\/strong\u003e 33.4dB\u003cbr\u003e\u003cstrong\u003eMax gain:\u003c\/strong\u003e 79.7dB\u003cbr\u003e\u003cstrong\u003eFrequency response:\u003c\/strong\u003e  20Hz to 20KHz +\/- 1dB\u003cbr\u003e\u003cstrong\u003eNoise:\u003c\/strong\u003e  127.7dB below input at 70dB gain measured against 200ohm input 20Hz to 20KHz bandwidth\u003cbr\u003e\u003cstrong\u003eHigh pass filter switch:\u003c\/strong\u003e 12dB\/8ve 3dB point 75Hz\u003cbr\u003e\u003cstrong\u003eHarmonic distortion:\u003c\/strong\u003e measured at 50dB gain –\u003cbr\u003e\u003cstrong\u003eAt 95Hz  2\u003csup\u003end\u003c\/sup\u003e order\u003c\/strong\u003e  -74dB, 3\u003csup\u003erd\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -80dB. (0.02%)\u003cbr\u003e\u003cstrong\u003eAt 1KHz  2\u003csup\u003end\u003c\/sup\u003e order\u003c\/strong\u003e -84dB, 3\u003csup\u003erd\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -72dB. (0.018%)\u003cbr\u003e\u003cstrong\u003eAt 3.5KHz 2\u003csup\u003end\u003c\/sup\u003e order\u003c\/strong\u003e -80dB, 3\u003csup\u003erd\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -63dB. (0.08%)\u003cbr\u003e\u003cstrong\u003ePhantom power switch:\u003c\/strong\u003e 48 volts\u003c\/p\u003e\n\u003cp\u003eThe power supply is integral with the audio board and has linear regulators powered from an encapsulated mains transformer.\u003c\/p\u003e\n\u003cp\u003eMains ground is internally connected to audio ground\u003cbr\u003eSupplied with 2m IEC mains cable\u003cbr\u003eRackmount ears supplied as standard\u003c\/p\u003e\n\u003cp\u003e100% manufactured in the UK\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMains supply:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e230 V AC 3VA (115V via internal links)\u003cbr\u003e\u003cstrong\u003ePower consumption:\u003c\/strong\u003e 3VA\u003cbr\u003e\u003cstrong\u003eDimensions:\u003c\/strong\u003e 275 (W) x 115 (D) x 42 (H)\u003cbr\u003e\u003cstrong\u003eShipping Weight:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e1.25Kg\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":55127204692342,"sku":"SALIMICAMPPAKSOLO","price":319.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/AliceMicAmpPAKTransformerSolowithoutUSB1.jpg?v=1736433870"},{"product_id":"alice-mic-amp-pak-duo-without-usb","title":"Alice Mic Amp PAK Duo without USB","description":"\u003ch2\u003eAlice Mic Amp PAK Duo without USB\u003c\/h2\u003e\n\u003cp\u003eThe Alice Mic Amp PAK is a dual-channel mic amp with audio transformer inputs and a sophisticated discrete input stage, gain control and balanced output.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTechnical Specification\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMin gain:\u003c\/strong\u003e 33.4dB\u003cbr\u003e\u003cstrong\u003eMax gain:\u003c\/strong\u003e 79.7dB\u003cbr\u003e\u003cstrong\u003eFrequency response:\u003c\/strong\u003e  20Hz to 20KHz +\/- 1dB\u003cbr\u003e\u003cstrong\u003eNoise:\u003c\/strong\u003e  127.7dB below input at 70dB gain measured against 200ohm input 20Hz to 20KHz bandwidth\u003cbr\u003e\u003cstrong\u003eHigh pass filter switch:\u003c\/strong\u003e 12dB\/8ve 3dB point 75Hz\u003cbr\u003e\u003cstrong\u003eHarmonic distortion:\u003c\/strong\u003e measured at 50dB gain –\u003cbr\u003e\u003cstrong\u003eAt 95Hz\u003c\/strong\u003e  2\u003csup\u003end\u003c\/sup\u003e order  -74dB, 3\u003csup\u003erd\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -80dB. (0.02%)\u003cbr\u003e\u003cstrong\u003eAt 1KHz\u003c\/strong\u003e  2\u003csup\u003end\u003c\/sup\u003e order -84dB, 3\u003csup\u003erd\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -72dB. (0.018%)\u003cbr\u003e\u003cstrong\u003eAt 3.5KHz\u003c\/strong\u003e 2\u003csup\u003end\u003c\/sup\u003e order -80dB, 3\u003csup\u003erd\u003c\/sup\u003e\u003cspan\u003e \u003c\/span\u003eorder -63dB. (0.08%)\u003cbr\u003e\u003cstrong\u003ePhantom power switch:\u003c\/strong\u003e 48 volts\u003c\/p\u003e\n\u003cp\u003eThe power supply is integral with the audio board and has linear regulators powered from an encapsulated mains transformer.\u003c\/p\u003e\n\u003cp\u003eMains ground is internally connected to audio ground\u003cbr\u003eSupplied with 2m IEC mains cable\u003cbr\u003eRackmount ears supplied as standard\u003c\/p\u003e\n\u003cp\u003e100% manufactured in the UK\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMains supply:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e230 V AC 3VA (115V via internal links)\u003cbr\u003e\u003cstrong\u003ePower consumption:\u003c\/strong\u003e 3VA\u003cbr\u003e\u003cstrong\u003eDimensions:\u003c\/strong\u003e 275 (W) x 115 (D) x 42 (H)\u003cbr\u003e\u003cstrong\u003eShipping Weight:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e1.25Kg\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":55127226024310,"sku":"SALIMICAMPPAKDUO","price":399.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/AliceMicAmpPAKTransformerSolowithoutUSB1_b72e5dd4-de02-43bd-926e-76d19efee444.jpg?v=1736250459"},{"product_id":"alice-828-mkiii-mixing-desk-grey-1","title":"Alice 828 MkIII Mixing Desk - Grey","description":"\u003ch2\u003eAlice 828 MkIII Mixing Desk - Grey\u003c\/h2\u003e\n\u003cp\u003eWe are now shipping the Alice 828 MK3.\u003c\/p\u003e\n\u003cp\u003eThe 828 series mixer went into production at the Alice factory in Windsor in 1976 and the last one was made there in 1986.\u003c\/p\u003e\n\u003cp\u003eThe Mk3 was designed by Ted Fletcher in 2019\/20 with production starting in August 2021. It only took 43 years for the MK3 version to be made!\u003c\/p\u003e\n\u003cp\u003eAs well as the standard gun metal gray, Alice have made 10 limited edition versions with relays on all three mic channels as standard. They are available in 3 colours: Chilli Red, Tango Orange \u0026amp; Midnight Blue. Please specify colour upon placing your order.\u003c\/p\u003e\n\u003cp\u003eMicrophone and mono line inputs \u0026amp; line outputs are transformer balanced.\u003cbr\u003eThree x microphone inputs c\/w 48v phantom powering.\u003cbr\u003eFive x stereo line inputs (with two having line\/RiAA amplification as standard).\u003cbr\u003eMicrophone position one has monitor cut and a remote control relay via the 9 pin D-Sub.\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":55127246209398,"sku":"SALI828MKIII","price":1750.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/828MkIIIMixingDeskGreyTop.jpg?v=1736251484"},{"product_id":"alice-828-mkiii-mixing-desk-with-8x-mic-and-line-channels","title":"Alice 828 MkIII Mixing Desk with 8x Mic and Line Channels","description":"\u003ch2\u003eAlice 828 MkIII Mixing Desk with 8x Mic and Line Channels\u003c\/h2\u003e\n\u003cp\u003eWe are now shipping the Alice 828 MK3 mixer with 8 mic \/ mono line inputs.\u003c\/p\u003e\n\u003cp\u003eThe 828 series mixer went into production at the Alice factory in Windsor in 1976 and the last one was made there in 1986.\u003c\/p\u003e\n\u003cp\u003eThe Mk3 was designed by Ted Fletcher during late 2019 with production starting in August 2021. It only took 43 years for the MK3 verison to be made!\u003c\/p\u003e\n\u003cp\u003e8 x microphone and mono line inputs \u0026amp; line outputs are transformer balanced.\u003cbr\u003eAll microphone inputs c\/w 48v phantom powering.\u003cbr\u003eMonitor cut and a remote control relays are available at time of ordering.\u003c\/p\u003e\n\u003cp\u003eIt comes in standard gun metal gray\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003ca href=\"https:\/\/www.alice.co.uk\/alice-828-mixer-mk3\/\"\u003eClick here\u003c\/a\u003e\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eto view the full specification and a video of Ted explaining the history of the product and the making of the Mk3.\u003c\/p\u003e\n\u003cp\u003eShipping weight: 10 kg\u003c\/p\u003e\n\u003cp\u003eMixers can be shipped with country specific mains plugs. Please advise when ordering your preference.\u003c\/p\u003e","brand":"Alice Soundtech","offers":[{"title":"Default Title","offer_id":55127442063734,"sku":"SALI828MKIII8CH","price":2250.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0256\/2988\/4462\/files\/Alice828MkIIIMixingDesk8xMicandLineChannelsTop.jpg?v=1736258019"}],"url":"https:\/\/studiocare.com\/collections\/alice-soundtech.oembed?page=2","provider":"Studiocare","version":"1.0","type":"link"}