Wisycom 40S Low Kit

Wisycom 40S Low Kit

The Wisycom 40S Low Kit is a professional high-end wireless system composed from 1 MCR42S Dual Receiver including the Digcom2, 1 BPA42 PTT OR BPA42 HPN base choice on request, 2 MTP40S double AA battery Transmitters, 1 VAP42 Carry Case and the MTP40S transmitter. The MTP40S is an extremely small and light pocket transmitter especially designed for professional wireless microphone applications. Very easy and quick to use thanks to an OLED display, dedicated buttons and a joggle selector. The MTP40S benefits from the latest Wisycom RF technology along with enhanced robustness against noise and inter-modulation.

Features

• Dual channel, true diversity in a modular stand-alone or slot-in format.
• Switching bandwidth up 232 MHz in the UHF range.
• 40 groups of 60 frequencies, fully user programmable.
• 1 x MTP 40s, 1 x MTP 41S Beltpack Transmitters
• Carry Case included

Specifications

• Frequency ranges:
• N 470 to 700 MHz
• M 566 to 798 MHz
• Switchable channels: 40 groups of 60 channels fully user programmable
• Switching-window: Up to 232 MHz
• Frequencies: Microprocessor controlled frequency synthesizer circuit, with 25 kHz minimum step. The frequencies are easily PC reprogrammable with the optional UPK Mini Programming Kit
• Frequency error: < ± 2.5 ppm, in the rated temperature range
• Temperature range: -10 to +55 °C
• Modulation: FM, with 50 μs de-emphasis
• Nominal deviation: ±40 kHz (Max. operating dev. = ± 60 kHz)
• Antenna input impedance: 50 ohm SMA type (SWR < 1:2; typ. 1:1.4)
• Sensitivity: 
• 2 μV ( 0 dBμV), for SND/N > 58 dB
• 5 μV (14 dBμV), for SND/N > 98 dB
• Amplitude response: < 0.5 dB (RF input sig.:6 dBμV to 100 dBμV)
• Co-channel rejection: > 2.5 dB
• Adjacent chan. selectivity: > 80 dB typical (for ch. spacing ≥ 400 kHz)
• Spurious rec. rejection: > 100 dB
• IF image rejection: > 90 dB
• Intermod. rejection: > 76 dB
• IIP3: > +10 dBm typical
• Spurious emissions: < 2 nW (typical = 0.1 pW)
• Noise Reduction system:
• ENR (Wisycom Extended-NR), noise optimized
• ENC (Wisycom Extended-NC), voice optimized & with reduced pre-emphasis 
• Others, compatible with most systems, through an internal DSP emulation of SA572, SA575 and Rms envelope compander chip set, fully user programmable
• AF bandwidth: 30 Hz to 20 kHz
• Frequency response: ± 0.5 dB in the 30 Hz to 19 kHz range
• Distortion: 0.3 % typical
• SND/D ratio (Analogue): 110 dB typical [*]
• SND/D ratio (AES3): >125 dB typical [*]
• POWER LEDs:
• 2 multicolor RGB LEDs to easy indicate Rx1 & Rx2 power status:
• GREEN, if “Receiver ON” with external power supply
• RED, if LEDs blinking indicates power supply status of transmitter
• slow blinking, at 25% battery capacity
• fast blinking, at 12.5% battery capacity
• RF LEDs:
• 2 multicolor RGB LEDs to easy indicate Rx1 & Rx2 RF status
• RED, if both receivers RF level is under squelch level
• GREEN, if signal above squelch level & antenna A (green) is active
• BLUE, if signal above squelch level & antenna B (blue) is active
• YELLOW, if signal above squelch and both antenna are used
• AUDIO LEDs:
• 2 multicolor RGB LEDs to easy indicates Rx1 & Rx2 audio status
• RED, if audio is muted because of squelch (or tone squelch if active)
• GREEN, if audio is active and tone squelch present
• BLUE, if audio is active and tone squelch not present
• Front buttons: Simple operation with 4 buttons to quickly monitor and setup the receiver One touch function for frequency scan and sync function
• Powering: 
• External = 5 to 18 Vdc (1.5 W max)
• Autonomous. = with optional BCA 42 Battery Module (5 x IEC-LR6 1.5V size-AA alkaline or rechargeable batteries)
• Dimensions: “Slot-in” end plate = 68 x 18 x 115 mm, “Stand-alone” end plate. = 68 x 18 x 135 mm
• Weight: 180g approx
• Analogue Audio Output: 
• Audio line-output electronically balanced on two 3 pin mini-XLR Female connector
• Audio line-output level Adjustable in one dB steps between -20 and +6 dBu (nominal) and MAX +12 dBu (peak deviation)
• Audio line-output imped. ≤ 200 ohm
• Push to Talk (PTT) Audio Output: electronically balanced on a 5 pin mini-XLR Male connector
• Digital Audio Output: 
• electronically balanced on 3 pin mini-XLR Male connector
• AES3 @ 48 kHz