DPA 5006A d:mension™ Surround Kit with 5 x 4006A, Clips, Windscreens in Peli Case
£7,775.00 ex. vat
DPA 5006A d:mension™ Surround Kit
The DPA d:dicate 5006A Surround Mic kit is designed to provide a multi-mic solution for decca tree and surround main array scenarios.
Consisting of five 4006A omni-directional condenser mics, matched to within 0.5dB of each other, the DPA standard tolerances are tuned even further to harmonise the mics with each other for a refined and balanced sound.
The natural sound, high sensitivity, low noise-floor and extremely linear frequency response from 10 Hz to 20 kHz (±2 dB) of the microphones make the DPA 4006As the perfect choice for all AB Stereo, Decca Tree or surround main array recordings. The precise reproduction, total transparency and natural-sounding clarity of a DPA 4006A microphone will provide you with a lifetime of satisfying listening.
The DPA 5006A comes packed in a hard wearing, heavy duty Peli case for transportation and protection, and all relevant mic clips and windshields are included.
DPA 5006A Surround Kit Features
- Five carefully matched microphones
- Perfect for Decca Tree + rear omnis surround array
- Specially useful for acoustically accurate reproductions
- PeliTM Case transportation and protection
DPA 5006A Specifications
- Directional pattern: Omnidirectional
- Principle of operation: Pressure
- Cartridge type: Pre-polarized condenser
- Frequency range: 10 Hz - 20 kHz
- Frequency range, ± 2 dB: 10 Hz - 20 kHz
- Sensitivity, nominal, ± 2 dB at 250 Hz: 40 mV/Pa; -28 dB re. 1 V/Pa
- Equivalent noise level, A-weighted: Typ. 15 dB(A) re. 20 µPa (maks. 17 dB(A))
- Equivalent noise level, ITU-R BS.468-4: Typ. 27 dB (max. 29 dB)
- S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): Typ. 79 dB(A)
- Total Harmonic Distortion (THD): < 1 % up to 139 dB SPL peak
- Dynamic range: Typ. 124 dB
- Max. SPL, peak before clipping: 147 dB
- Switchable attenuator: 0 dB / -20 dB
- Output impedance: < 200 ohm
- Minimum load impedance: 2 kohm
- Cable drive capability: 100 m (328 ft)
- Output balance principle: Impedance balancing with Active Drive
- Common Mode Rejection Ratio (CMRR): > 60 dB
- Power supply (for full specifications): 48 V Phantom power (± 4 V)
- Current consumption: 2.8 mA
- Connector: XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
- Color: Matte black
- Weight: 163 g (5.7 oz)
- Microphone diameter: 16 - 19 mm (0.6 - 0.75 in)
- Capsule diameter: 16 mm (0.6 in)
- Microphone length: 170 mm (6.7 in)
- Output voltage, RMS: > 5 V
- Polarity: +V at pin 2 for positive sound pressure
- Temperature range: -40 °C to 50 °C (-40 °F to 122 °F)
- Relative Humidity (RH): Up to 90%
- Matching tolerance (freqency response, sensitivity): ± 0.5 dB
- Phase deviation for kit: < 5°