DPA ST4015A - d:dicate™ 4015A Stereo Pair with Clips and Windscreens in Peli Case
£2,322.00 ex. vat
DPA ST4015A - d:dicate 4015A Pair
The DPA d:dicate ST4015A Stereo Pair is wide cardioid pick-up condenser mic set that delivers the same clear, neutral and honest sound as the DPA 4011A, but is designed to combine the features of both an omni-directional and cardioid mic to widen the traditional cardioid pick-up pattern. When paired. the 4015A offers the same kind of performance as a cardioid mic pair but with a much wider field of view, yet without the rear pick up of an omni-directional mic set.
When close miking certain dynamic instruments that produce varying tones from different positions, a cardioid mic can sometimes be too focused to pick up every element. A wide cardioid (hemispheric) mic expands the capsules field of view to encompass a wider pick up angle, but retains the rear rejection and sound separation that omni capsules lack.
Even though the standard tolerances on DPA Reference Standards are extremely low, a stereo match is even closer. The specially selected DPA 4015A microphones in the DPA ST4015A are matched within ±1 dB on both frequency response and sensitivity.
The mic has a linear neutral off axis response and any spill is subtly attenuated and is capable of handling high SPL of up to 159dB without distortion; perfect for use on drum kits and brass.
DPA ST4015A Features
- Wide pick-up area and natural sound
- Ambience pickup with some directionality
- Carefully matched within ±1 dB
- PeliTM Case transportation and protection
DPA ST4015A Specifications
- Directional pattern: Wide cardioid
- Principle of operation: Pressure gradient
- Cartridge type: Pre-polarized condenser
- Frequency range: 20 Hz - 20 kHz
- Frequency range, ± 2 dB, at 60 cm: 40 Hz - 20 kHz
- Sensitivity, nominal, ± 2 dB at 1 kHz: 10 mV/Pa; -40 dB re. 1 V/Pa
- Equivalent noise level, A-weighted: Typ. 18 dB(A) re. 20 µPa (max. 20 dB(A))
- Equivalent noise level, ITU-R BS.468-4: Typ. 25 dB (correct with the attenuator in 0 dB or -20 dB setting)
- S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): Typ. 76 dB(A)
- Total Harmonic Distortion (THD): < 1 % up to 139 dB SPL peak
- Dynamic range: Typ. 121 dB
- Max. SPL, peak before clipping: 159 dB
- Switchable attenuator: 0 dB / -20 dB
- Output impedance: < 200 ohm
- Minimum load impedance: 2 kohm
- Cable drive capability: 100 m (328 ft)
- Output balance principle: Impedance balancing with Active Drive
- Common Mode Rejection Ratio (CMRR): > 60 dB
- Power supply (for full specifications): 48 V Phantom power (± 4 V)
- Current consumption: 2.8 mA
- Connector: XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
- Color: Matte black
- Weight: 158 g (5.6 oz)
- Microphone diameter: 19 mm (0.75 in)
- Capsule diameter: 19 mm (0.75 in)
- Microphone length: 170 mm (6.7 in)
- Output voltage, RMS: > 5 V
- Polarity: +V at pin 2 for positive sound pressure
- Temperature range: -40 °C to 45 °C (-40 °F to 113 °F)
- Relative Humidity (RH): Up to 90%
- Matching tolerance: ± 1 dB
- Phase deviation for kit: < 10°